On the basis of inheriting the advantages of rigid frame, symmetrical structure and strong stability, the machine tool has introduced the international advanced concept of dynamic rigidity and optimized the design of mobile parts. The machine tool has great torque and fast response characteristics, and it is suitable for various mechanical processing fields, such as automobile, mould, aerospace, military industry, hardware and so on.
The overall layout of the machine tool is a frame structure, the base is fixed, and the worktable is moved from the base to the base of X.
1, high rigidity, long lasting accuracy retention
?The machine is mainly large: base, table, column, beam, slide, slide are made of high quality resin sand molding, high strength and high quality cast iron, with heat treatment process improvement to eliminate the residual stress, and the layout of sufficient reinforcement plate, ensure the machine has enough strength and rigidity and high stability.
?The XY axle adopts imported heavy load roller guide, which has strong rigidity and good dynamic precision.
?The three axle drive adopts Taiwan large diameter grinding double nut ball screw rod, which has compact structure, smooth movement and high precision. The silk rod support is supported by the Japanese imported silk rod support bearing, which is prestretched at both ends to eliminate the precision loss caused by the thermal elongation. A stable high rigid mechanical transmission system is made up.
?The staircase structure, the cross section of the beam is large, the distance of the guide rail is large, the center of the spindle is short, the turning moment is small, and the structure has a good rigidity.
?The high rigidity Taiwan produces the Longmen special-purpose spindle, uses the lubricating grease lubrication, enables the spindle bearing to obtain the constant and reliable lubrication, is economical and environmental protection, and has realized the long term free maintenance.
2, high precision and high dynamic response characteristics
?The spindle is supported with three points to make the spindle get high rigidity and high spindle rotary precision.
?The XY axis roller guide has high accuracy, large load and only 0.002 friction coefficient. It reduces the phenomenon of low speed crawling and achieves good positioning accuracy and high dynamic response characteristics.
?The Z axis adopts the structure of the nitrogen balance cylinder, and its dynamic response speed is higher than the traditional hydraulic balance structure, and its structure is simple and the maintenance is convenient.
3. High efficiency
?The spindle speed is up to 24000rpm, the three axis can move up to 12m/min quickly, and the cutting feed speed can reach 12m/min.
1, CNC function
The minimum resolution: 1um maximum moving speed: 12m/min straight line, arc, helix interpolation automatic deceleration control return reference point coordinate setting MDI function of M, S, T graphics processing static simulation and real-time tracking of fixed circular milling
2, CNC programming
The smallest unit of programming: 0.001mm, 0.001 degrees maximum program size: 99999.999 rows: 2 billion for maximum programming metric / inch absolute / relative programming instruction programming macro programming subroutine calls plane selection of workpiece coordinate setting local coordinate coordinate rotation, zoom and mirror set
3. Editors
Background edit character lookup and replace file deletion and copy
4. Display
Chinese menu function, graphic display, status display, current position display program, display program error, display operation error, display alarm display, coordinate axis setting, display spindle speed self diagnosis function.
5, interpolation function
Linear interpolation, maximum four axis circular interpolation spiral interpolation
6, tool compensationTool length compensation for tool radius compensation
7. Operation
Handheld unit of color LCD display
8. Operation mode
Automatic single segment MDI point moving incremental feed incremental feed manual / automatic back reference point feed to keep empty operation
9. Feed shaft function
Feed trimming 0% to 150% quickly shift 0%, 25%, 50%, 100%
10. The function of the spindle
Spindle speed: can be programmed by PLC to control spindle repair 50% - 120%
11. Other functions
RS232 - C communication interface program protection function
1. Temperature
In order to keep the accuracy of machine tools in the range of standard guarantee value, we should ensure that the working environment temperature is 17 degrees ~25, and maintain the temperature change of 24 hours in the range of + 2 degrees.
If the precision of the processed parts is lower than the precision of the machine tool factory, the ambient temperature range can be relaxed to 10 ~38 C.
humidity
Continuous: less than 75% (non - condensation) short time: less than 95% (non - condensation)
2.Altitude
Below 1000M3. Conditions for installation of places
The concentration of dust in the air should not be greater than 10mg/m3. No acid, salt and corrosive gas in the air
4. Power supply
5, 3 phase 380V + 10%; 50HZ;
6. Capacity of power source
15KVA
7. Grounding
Good grounding is required. Each machine tool is recommended to be grounded alone. The wire diameter of the grounding wire should not be less than the power line.
Six, marking the content of supply
NC machining center milling machine DX-650
The following configuration and attachments are included:
1. Numerical control system and servo motor and driving unit
2. The main shaft blowing device
3. Full automatic lubrication system
4, cutting and cooling system, increase the high pressure water pump 10-15KG
5. Heat exchange system of electric box
6, chip system, after the water,
7, working light, mechanical abnormal state warning lamp
8, RS232C transmission interface, 220V power interface
9, hand pulse generator
10. Horizontal regulation system (including pads and adjusting bolts)
11. The Basic Toolbox (including one set of six angle wrenches, one word from ten, one RS232 transmission line)
12, 380V/220V 50HZ transformer
13. Outer shield
14. Certificate of qualification
15, mechanical / electrical instructions
16. System operation / programming manual
17. Packing list
Seven, main specifications and technical parameters
Product model | DX- 650 | Unit | |
Workbench | Workbench size | 600X500 | mm |
Worktable bearing | 0.3 | T | |
T groove width | 5X14 | mm | |
Processing range | X axis stroke | 600 | mm |
Y axis stroke | 500 | mm | |
Z axis stroke | 245 | mm | |
Principal axis | Cone type | BT30 |
|
Nail specification | 45 degrees |
| |
Speed range | 2000-24000 | rpm | |
Spindle motor power | 5.5 electric spindle | KW | |
Feed | Cutting feed speed range | 10-10000 | mm/min |
X axis fast moving | 12000 | mm/min | |
Y axis fast moving | 12000 | mm/min | |
Z axis fast moving | 12000 | mm/min | |
System configuration | New generation 21MA |
| |
The knife | Okada 12 knives | ||
Shape size | Three axis guide gauge (XYZ) | Y/Z axis -30# line rail |
|
X axis 30# line rail | |||
Three axis wire rod specification (XYZ) | X axis 2510 |
| |
Y axis 2510 | |||
Z axis 2510 | |||
Bearing specification | X axis 20TAC47B |
| |
Y axis 20TAC47B | |||
Z axis 20TAC47B | |||
Mainframe size | about 1900X1700X2100 | mm | |
Host weight | about 3.2 | T | |
According to the different styles and batches of the customer, please refer to the foundation map.
Eight. List of main purchase parts
Serial number | Name | Manufacturer | Special order |
1 | numerical control system | New generation 21MA |
|
2 | Wire rod | Taiwan silver or Rexroth |
|
3 | Wire rod bearing | NSK, NTN, Japan |
|
4 | Ball linear guide | Taiwan silver or Rexroth |
|
5 | principal axis | Wuxi Rong Hua |
|
6 | Play knife cylinder | investment from Taiwan |
|
7 | Precision lock nut | Taiwan silver tin |
|
9 | Main components of the lubrication system | Taiwan baoteng |
|
10 | Main components of pneumatic system | Taiwan Yadeke |
|
11 | Main elements of nitrogen balance | domestic |
|
12 | Main components of electrical system | Schneider |
|
13 | Towline | Veroc | |
14 | X direction steel shield | Hong Wang | |
15 | Y organ shield | Hong Wang |
|
16 | Water pump | investment from Taiwan |
Nine. The configuration of machine tool selection (need to pay for another)
Serial number | project | Remarks | Selection |
1 |
|
|
|
2 | The knife | 12 knives |
|
Ten. Precautions
The customer must be in strict accordance with our foundation drawing foundation, if need to change, must obtain our written confirmation, otherwise it will not guarantee the accuracy of machine tool.Acceptance criteria and methods
1. The acceptance of machine tools is carried out in two times: pre acceptance and final acceptance.
2, pre acceptance in Kunshan Liangjiang Pml Precision Mechanism Ltd, machine tool inspection requirements refer to "GB/T25658.1-2010 CNC machining center milling machine test conditions of precision test, such as" special requirements according to an agreed sample test cutting test, and the two sides agreed to the machining accuracy and process capability.
The 3 and final acceptance in the user plant, installed and debugged by the Kunshan Pml Precision Mechanism Ltd will send, in principle only acceptance precision: if any environment and corresponding software and hardware facilities, we can check with precision table.
4. The samples, cutting tools and special fixtures required for sample cutting are provided by the buyer, except for special stipulations.
5. Note:
1) if the machine is shipped to the buyer's factory for 30 days, the installation and commissioning of the machine can not be carried out because of the buyer's cause, which is regarded as the acceptance of the machine tool.
2) the precision index of the machine tool is tested according to the acceptance accuracy table of the technical agreement. If the buyer has any objection to the test result, the buyer can prepare the testing equipment and appoint the national certification inspecting party to recheck. If the test result is consistent with the accuracy table of the technical agreement, the cost incurred during the inspection period will be borne by the buyer. The buyer must seal the machine tool before testing, and if the buyer opens the machine, it is deemed to be qualified.
3) it is the basic requirement for the precision processing to keep the ambient temperature as the uniform value. According to the rule of GB/T17421.3-2009 (ISO 1:2002), all linear measurements should be done at room temperature of 20 degrees, and it is required to measure the heat balance between the measuring instrument and the tested object (such as machine tool) and the surrounding environment.
